Beispielkonfiguration - Compaq Deskpro EN
Aus VDR Wiki
Version vom 29. August 2013, 21:24 Uhr von Hulk (Diskussion | Beiträge)
Inhaltsverzeichnis |
Vor/Nachteile
- + WAKE ON LAN on Board (nur mit e100 und nicht mit epro100, ggf. /lib/modules/*/modules.pcimap anpassen)
- + Suspend to Ram / Disk
Bilder
Hardware
On Board
shell> lspci -vv
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [88] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation 82815 CGC [Chipset Graphics Controller] (rev 02) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation Unknown device 0019
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at 40400000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 40000000-403fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 01) (prog-if 80 [Master])
Subsystem: Intel Corporation Unknown device 2411
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at 2460 [size=16]
00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 2411
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 4: I/O ports at 2440 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 01)
Subsystem: Compaq Computer Corporation Unknown device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2000 [size=256]
Region 1: I/O ports at 2400 [size=64]
02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller (rev 01)
Subsystem: Compaq Computer Corporation EtherExpress PRO/100 VM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
+
shell> cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 8 model name : Pentium III (Coppermine) stepping : 6 cpu MHz : 863.936 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1729.91
shell> cat /proc/meminfo MemTotal: 512152 kB MemFree: 29824 kB Buffers: 94052 kB Cached: 312880 kB SwapCached: 4 kB Active: 89440 kB Inactive: 334976 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 512152 kB LowFree: 29824 kB SwapTotal: 125488 kB SwapFree: 125148 kB Dirty: 4192 kB Writeback: 0 kB Mapped: 25000 kB Slab: 47308 kB CommitLimit: 381564 kB Committed_AS: 112040 kB PageTables: 412 kB VmallocTotal: 507896 kB VmallocUsed: 6364 kB VmallocChunk: 501432 kB
shell> lspci -vv
02:04.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 40001000 (32-bit, non-prefetchable) [size=512]
02:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Siemens/Technotrend/Hauppauge DVB card rev1.3 or rev1.5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40100000 (32-bit, non-prefetchable) [size=512]
LIRC empfänger von http://www.zapway.de
Module
| Hardware | Module |
|---|---|
| 82815 CGC [Chipset Graphics Controller] | agpgart |
| 82801BA/BAM AC'97 Audio | snd_intel8x0 |
| 82801BA/BAM/CA/CAM Ethernet Controller | e100 oder epro100 |
| 82801BA/BAM USB | usb_core + uhci_hcd |
Quelle: http://www.2xlc.de/travelmate.html
Konfigurations-Files
/etc/modprobe.conf
# --- BEGIN: Generated by ALSACONF, do not edit. --- # --- ALSACONF version 1.0.14 --- alias snd-card-0 snd-intel8x0 alias sound-slot-0 snd-intel8x0 # --- END: Generated by ALSACONF, do not edit. ---
Linux Kernel v2.6.20.3 Configuration
Device Drivers --->
Sound --->
<M> Sound card support
Advanced Linux Sound Architecture --->
<M> Advanced Linux Sound Architecture
[*] Support old ALSA API
[*] Verbose procfs contents
PCI devices --->
<M> Intel/SiS/nVidia/AMD/ALi AC97 Controller
/etc/X11/xorg.conf
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
# (Type "man /etc/X11/xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "ServerFlags"
Option "AutoAddDevices" "False"
EndSection
Section "Files"
FontPath "/usr/share/X11/fonts/misc"
FontPath "/usr/share/X11/fonts/cyrillic"
FontPath "/usr/share/X11/fonts/100dpi/:unscaled"
FontPath "/usr/share/X11/fonts/75dpi/:unscaled"
FontPath "/usr/share/X11/fonts/Type1"
FontPath "/usr/share/X11/fonts/CID"
FontPath "/usr/share/X11/fonts/100dpi"
FontPath "/usr/share/X11/fonts/75dpi"
# paths to defoma fonts
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/CID"
EndSection
Section "Module"
Load "GLcore"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
#Load "type1"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc104"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
EndSection
Section "Device"
Identifier "Intel Corporation 82815 CGC [Chipset Graphics Controller]"
#Driver "i810"
Driver "intel"
BusID "PCI:0:2:0"
EndSection
Section "Monitor"
Identifier "KDS VS-70"
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Intel Corporation 82815 CGC [Chipset Graphics Controller]"
Monitor "KDS VS-70"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
EndSection
Section "DRI"
Mode 0666
EndSection
Linux Kernel v2.6.20.3 Configuration
Device Drivers --->
Graphics support --->
<*> Support for frame buffer devices
[*] VESA VGA graphics support
<*> Intel 810/815 support (EXPERIMENTAL)
[*] use VESA Generalized Timing Formula
Console display driver support --->
[*] Video mode selection support
<*> Framebuffer Console support
Ergänzung WOL
Ergänzung für WOL.
#!/bin/sh # # /etc/rc.d/net: start/stop network # case $1 in start) modprobe e100 # loopback /sbin/ip addr add 127.0.0.1/8 dev lo broadcast + scope host /sbin/ip link set lo up # ethernet #/sbin/ip addr add 192.168.1.100/24 dev eth0 broadcast + #/sbin/ip link set eth0 up # default route #/sbin/ip route add default via 192.168.178.10 #/sbin/ifconfig lo 127.0.0.1 /sbin/dhcpcd -I "" -t 10 -h $HOSTNAME eth0 ;; stop) #/sbin/ip route del default #/sbin/ip link set eth0 down #/sbin/ip addr del 192.168.1.100/24 dev eth0 #/sbin/ip link set lo down #/sbin/ip addr del 127.0.0.1/8 dev lo /usr/bin/killall -q /sbin/dhcpcd /sbin/ip link set lo down /sbin/ip addr del 127.0.0.1/8 dev lo rmmod e100 if grep -qs ^PCI0.*disabled /proc/acpi/wakeup ; then echo -n PCI0 >> /proc/acpi/wakeup fi ;; restart) $0 stop $0 start ;; *) echo "usage: $0 [start|stop|restart]" ;; esac # End of file
OS
shell> uname -a Linux crux 2.6.24 #3 SMP Thu Jul 3 18:13:25 CEST 2008 i686 Pentium III (Coppermine) GenuineIntel GNU/Linux
Bios Einstellungen
Systeminformationen
Energiesparmodus deaktivieren für ACPI Funktion
Systemstartoptionen
PCI Geräte
Geräte Optionen
