Beispielkonfiguration - Compaq Deskpro EN

Aus VDR Wiki
Wechseln zu: Navigation, Suche

Inhaltsverzeichnis

Vor/Nachteile

  • + WAKE ON LAN on Board (nur mit e100 und nicht mit epro100, ggf. /lib/modules/*/modules.pcimap anpassen)
  • + Suspend to Ram / Disk

Bilder

Gehäuse

Hardware

On Board

shell> lspci -vv

00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [88] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation 82815 CGC [Chipset Graphics Controller] (rev 02) (prog-if 00 [VGA])
        Subsystem: Compaq Computer Corporation Unknown device 0019
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M]
        Region 1: Memory at 40400000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 01) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 00001000-00001fff
        Memory behind bridge: 40000000-403fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 01) (prog-if 80 [Master])
        Subsystem: Intel Corporation Unknown device 2411
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Region 4: I/O ports at 2460 [size=16]

00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev 01) (prog-if 00 [UHCI])
        Subsystem: Intel Corporation Unknown device 2411
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 10
        Region 4: I/O ports at 2440 [size=32]

00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 01)
        Subsystem: Compaq Computer Corporation Unknown device 000b
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 5
        Region 0: I/O ports at 2000 [size=256]
        Region 1: I/O ports at 2400 [size=64]

02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller (rev 01)
        Subsystem: Compaq Computer Corporation EtherExpress PRO/100 VM
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at 1000 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

+

shell> cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 8
model name      : Pentium III (Coppermine)
stepping        : 6
cpu MHz         : 863.936
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips        : 1729.91
shell> cat /proc/meminfo
MemTotal:       512152 kB
MemFree:         29824 kB
Buffers:         94052 kB
Cached:         312880 kB
SwapCached:          4 kB
Active:          89440 kB
Inactive:       334976 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:       512152 kB
LowFree:         29824 kB
SwapTotal:      125488 kB
SwapFree:       125148 kB
Dirty:            4192 kB
Writeback:           0 kB
Mapped:          25000 kB
Slab:            47308 kB
CommitLimit:    381564 kB
Committed_AS:   112040 kB
PageTables:        412 kB
VmallocTotal:   507896 kB
VmallocUsed:      6364 kB
VmallocChunk:   501432 kB
shell> lspci -vv

02:04.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
        Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 66 (3750ns min, 9500ns max)
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at 40001000 (32-bit, non-prefetchable) [size=512]

02:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
        Subsystem: Technotrend Systemtechnik GmbH Siemens/Technotrend/Hauppauge DVB card rev1.3 or rev1.5
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 66 (3750ns min, 9500ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at 40100000 (32-bit, non-prefetchable) [size=512]

LIRC empfänger von http://www.zapway.de

modul%20small.jpg

Module

Hardware Module
82815 CGC [Chipset Graphics Controller] agpgart
82801BA/BAM AC'97 Audio snd_intel8x0
82801BA/BAM/CA/CAM Ethernet Controller e100 oder epro100
82801BA/BAM USB usb_core + uhci_hcd

Quelle: http://www.2xlc.de/travelmate.html

Konfigurations-Files

/etc/modprobe.conf

Datei
/etc/modprobe.conf
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF version 1.0.14 ---
alias snd-card-0 snd-intel8x0
alias sound-slot-0 snd-intel8x0
# --- END: Generated by ALSACONF, do not edit. ---


Linux Kernel v2.6.20.3 Configuration

Device Drivers  --->
    Sound  --->
        <M> Sound card support 
            Advanced Linux Sound Architecture  --->
               <M> Advanced Linux Sound Architecture
               [*]   Support old ALSA API
               [*]   Verbose procfs contents
                     PCI devices  --->
                         <M> Intel/SiS/nVidia/AMD/ALi AC97 Controller

/etc/X11/xorg.conf

Datei
/etc/X11/xorg.conf
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
# (Type "man /etc/X11/xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
    FontPath    "/usr/share/X11/fonts/misc"
    FontPath    "/usr/share/X11/fonts/cyrillic"
    FontPath    "/usr/share/X11/fonts/100dpi/:unscaled"
    FontPath    "/usr/share/X11/fonts/75dpi/:unscaled"
    FontPath    "/usr/share/X11/fonts/Type1"
    FontPath    "/usr/share/X11/fonts/CID"
    FontPath    "/usr/share/X11/fonts/100dpi"
    FontPath    "/usr/share/X11/fonts/75dpi"
        # paths to defoma fonts
    FontPath    "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
    FontPath    "/var/lib/defoma/x-ttcidfont-conf.d/dirs/CID"
EndSection

Section "Module"
    Load    "GLcore"
    Load    "i2c"
    Load    "bitmap"
    Load    "ddc"
    Load    "dri"
    Load    "extmod"
    Load    "freetype"
    Load    "glx"
    Load    "int10"
    Load    "type1"
    Load    "vbe"
EndSection

Section "InputDevice"
    Identifier    "Generic Keyboard"
    Driver        "kbd"
    Option        "CoreKeyboard"
    Option        "XkbRules"    "xorg"
    Option        "XkbModel"    "pc104"
    Option        "XkbLayout"    "us"
EndSection

Section "InputDevice"
    Identifier    "Configured Mouse"
    Driver        "mouse"
    Option        "CorePointer"
    Option        "Device"        "/dev/input/mice"
    Option        "Protocol"        "ImPS/2"
    Option        "Emulate3Buttons"    "true"
    Option        "ZAxisMapping"        "4 5"
EndSection

Section "Device"
    Identifier    "Intel Corporation 82815 CGC [Chipset Graphics Controller]"
    Driver        "i810"
    BusID        "PCI:0:2:0"
EndSection

Section "Monitor"
    Identifier    "KDS VS-70"
    Option        "DPMS"
EndSection

Section "Screen"
    Identifier    "Default Screen"
    Device        "Intel Corporation 82815 CGC [Chipset Graphics Controller]"
    Monitor        "KDS VS-70"
    DefaultDepth    24
    SubSection "Display"
        Depth        1
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Depth        4
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Depth        8
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Depth        15
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Depth        16
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Depth        24
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
EndSection

Section "ServerLayout"
    Identifier    "Default Layout"
    Screen        "Default Screen"
    InputDevice    "Generic Keyboard"
    InputDevice    "Configured Mouse"
EndSection

Section "DRI"
    Mode    0666
EndSection


Linux Kernel v2.6.20.3 Configuration

Device Drivers  --->
   Graphics support  --->
      <*> Support for frame buffer devices
      [*]   VESA VGA graphics support
      <*>   Intel 810/815 support (EXPERIMENTAL)
         [*]   use VESA Generalized Timing Formula
      Console display driver support  --->
         [*]   Video mode selection support
            <*> Framebuffer Console support

OS

shell> uname -a
Linux crux 2.6.15.6 #4 Sun Aug 6 22:05:33 CEST 2006 i686 pentium3 i386 GNU/Linux

Bios Einstellungen

Systeminformationen
Energiesparmodus deaktivieren für ACPI Funktion
Systemstartoptionen
PCI Geräte
Geräte Optionen